Differences

This shows you the differences between two versions of the page.

--- countour_shuttlexpress [2020/12/02 11:03] – created rjt
+++ contour_shuttlexpress [2024/05/30 08:29] – VIW link, more info on Linux setup and reorganising rjt
@@ Line 7: / Line 7: @@
   - An infinitely spinning dial with clicky movement. Good for stepping through a clip frame-by-frame.
-  - Another dial with limited movement that snaps back into place. Useful for fast-forwarding and re-winding.
+  - Another dial with limited movement (70° each side, I think) that snaps back into place. Useful for fast-forwarding and re-winding.
   - Five mouse-like buttons.
+There are larger versions that add more buttons.
 ===== Setup =====
 ==== Linux ====
-To use in [[linux]] and [[Kdenlive]] you will need to add a [[udev]] rule.
+NB: I've got it working in [[kdenlive]] without installing anything (see below), but I think for wider use you have to use one of these:
-  - Plug-in the shuttle, use ''lsusb'' and note the ID info. ''ID 0b33:0020'' in my case, but in the example on the Kdenlive]] documentation the //product ID// is ''0030''.
+  * [[github>threedaymonk/shuttlexpress]]
+  * [[github>SERVCUBED/ShuttlePRO]]
+    * [[github>agraef/ShuttlePRO]] | [[aur>shuttlepro-git]]
+      * [[github>SERVCUBED/ShuttlePRO]] | [[aur>shuttlepro-v2-git]]
+        * NB: I had to grab the example config from Github, because the makefile in this fork doesn't install it.
+  * [[github>irontoby/shuttleit]]
+=== Kdenlive ===
+You need to make a [[udev]] rule and then you can configure things in Kdenlive's settings:
+  - Plug-in the shuttle, use ''lsusb'' and note the ID info. ''ID 0b33:0020'' in my case, but in the example on the Kdenlive documentation the //product ID// is ''0030''.
   - Create a file in ''/etc/udev/rules.d'' (for example ''90-shuttlexpress.rules'' and add the line:\\ <code>SUBSYSTEMS=="usb", ATTRS{idVendor}=="0b33", ATTRS{idProduct}=="0020", MODE="0444"</code> where ''0b33'' is the first part of the ID you noted, and ''0020'' is the second.
   - Restart the udev stuff with ''# udevadm control %%--%%reload'' and ''# udevadm trigger''.
@@ Line 23: / Line 36: @@
 === See Also ===
-  * [[github>threedaymonk/shuttlexpress]]
-  * [[github>SERVCUBED/ShuttlePRO]]
-  * [[github>irontoby/shuttleit]]
-  * [[aur>shuttlepro-git]]
-  * [[aur>shuttlepro-v2-git]]
   * [[https://www.lwks.com/index.php?option=com_kunena&func=view&catid=25&id=72223&Itemid=81|ShuttlePROv2 working with Linux !]]
+==== See Also ====
+  * [[github>EMATech/OpenContourShuttle]] - In development, maybe Windows-only so far (haven't tested). Has a GUI for configuration.
+===== See Also =====
+  * [[https://videogameinterface.wiki/index.php/ShuttleXpress|ShuttleXpress]] on the [[Videogame Interface Wiki]].
+  * [[https://manual.ardour.org/using-control-surfaces/Countour_Design/|Using the Contour Design Shuttle Devices]] in the [[Ardour]] manual.
 {{tag>Contour hardware guide linux input setup}}